Correct installation of driving lines
2021-09-26 08:05:07
The characteristics of the traffic trolley line and the characteristics of the trolley line are actually similar. There are unipolar slip lines and multi-polar slip lines. According to the number of vehicles, the size of the current, and the size of the voltage, different types of trolley lines are selected or formed. Multi-line trolley wire. Driving trolley line is used as a special trolley line for driving. In the use process, special attention should be paid to the points of use. If dust is used in the environment, excessive dust may cause the trolley line to be powered off. Whether the environment is corrosive can easily cause leakage of the housing of the trolley line. Still need to observe the temperature in the environment, according to different environmental conditions, make different adjustment measures.
Installation of the trolley line: Firstly, the angle bracket of the trolley wire should be installed and welded, and then the lifting trolley and fixing bracket should be installed. Then fix the trolley wire under the pylon and the holder and install the power input. Use a wire contact connector to connect the wires and install the sheath and end cap. Finally, the slide wire collector penetrates into the current collector fixed bracket, and the distance between the trolley slide wire and the trolley wire collector is adjusted.
The trolley line should pay special attention to emergencies in the course of use. If the handling is not good, it can easily cause damage to the trolley line, and more serious ones can easily cause safety accidents. The more common emergencies are that the trolley wire is not fixed on the trolley wire support and the original track is offset. In this case, we need to cut off the power supply for the first time and correct it as soon as possible. We should try to avoid this kind of thing when we use the trolley wire. The correct method is to cut off the power supply and check all the wire rod fixing brackets. With reinforcement, the interval time is preferably about 3 months. There are also periodic inspections of the abrasion of the carbon brushes of the trolley wire collectors. If the carbon brushes wear more than two-thirds of the original brushes, they must be replaced. Try not to wear the brushes too much, because this will Causes a lot of damage to the trolley line. Because the quality of the trolley line is uneven, during the use process, it must be observed constantly whether the casing of the trolley line is deformed, broken or worn, and must be replaced in time to avoid the risk of electric shock.
Installation of the trolley line: Firstly, the angle bracket of the trolley wire should be installed and welded, and then the lifting trolley and fixing bracket should be installed. Then fix the trolley wire under the pylon and the holder and install the power input. Use a wire contact connector to connect the wires and install the sheath and end cap. Finally, the slide wire collector penetrates into the current collector fixed bracket, and the distance between the trolley slide wire and the trolley wire collector is adjusted.
The trolley line should pay special attention to emergencies in the course of use. If the handling is not good, it can easily cause damage to the trolley line, and more serious ones can easily cause safety accidents. The more common emergencies are that the trolley wire is not fixed on the trolley wire support and the original track is offset. In this case, we need to cut off the power supply for the first time and correct it as soon as possible. We should try to avoid this kind of thing when we use the trolley wire. The correct method is to cut off the power supply and check all the wire rod fixing brackets. With reinforcement, the interval time is preferably about 3 months. There are also periodic inspections of the abrasion of the carbon brushes of the trolley wire collectors. If the carbon brushes wear more than two-thirds of the original brushes, they must be replaced. Try not to wear the brushes too much, because this will Causes a lot of damage to the trolley line. Because the quality of the trolley line is uneven, during the use process, it must be observed constantly whether the casing of the trolley line is deformed, broken or worn, and must be replaced in time to avoid the risk of electric shock.
China Angle Bending Machine Suppliers
HYDRAULIC Bending machine
Applicable Industry:Used for bending of angles in the field of steel tower industry.
The equipment possesses independent hydraulic power system and electric controlling system.
The hydraulic system uses the electromagnetic valve to reverseAngle Bending Machine,Angle Iron Bender Machine,Angle Iron Bending Machine,Plate Bending Machine
Shandong ShuoFang Environmental Technology Co., Ltd. , https://www.chinafincnc.com