How to deal with the six common problems in winter car maintenance
In the winter, the closet is full of cold equipment, so are you prepared for the season of your car? Let me work together to make a comprehensive inspection and full equipment for the car.
First, the appearance of conservation:
(1) The car should be washed in time after snow days to remove snow water with acidic and corrosive substances, so as to avoid damage to car paint and premature rust.
(b) Washing vehicles in winter should use warm water. Do not rinse directly with cold water. In particular, after the engine is warmed up, the cold water wash cools down quickly, causing paint cracking on the hood surface. After washing, promptly open the door to dry the water traces, prevent the residual water from freezing at the seams, freeze the door, and do not force the switch when the windows are frozen.
Second, oil conservation:
(1) Special oil should be replaced in winter. To prevent the viscosity of ordinary lubricants from deteriorating due to the drop in temperature, resulting in difficulty in cold start of the car, and serious accidents such as the burning of the bearing bush and the shaft.
(b) The freezing point of the antifreeze should be lower than the minimum temperature of about 10°C in the area, at least once every two years. Water has been added to the antifreeze and the antifreeze must be replaced.
Third, electrical maintenance:
(a) The winter automobile consumes a large amount of electricity and it is necessary to provide timely battery care. Remove oxides from the battery headers and add distilled water. Too low a temperature will greatly reduce the battery capacity and it is better to perform a thorough charge. The average battery life is two to three years. If the battery has reached the end of its useful life, especially the automatic car, it is best to replace it in advance to prevent accidents.
(2) When the cold start is difficult, it shall be started again every 30 seconds or so. Continuous ignition shall be avoided to prevent the starter from being damaged and the battery draining power.
(C) The temperature difference between the inside and the outside of the car in winter is large, and the windows are likely to fog and affect the line of sight. Therefore, it is necessary to maintain the electric heating wire of the windshield, side window air outlet and rear window in good condition.
(4) In the winter, the vehicle should be started by ignition. After the engine is working normally, the headlights and other electrical equipment should be switched on. When the vehicle is parked, the electrical appliances should be turned off first, and then the flame should be turned off. The parking should not use as much power as possible, especially the power windows and headlights. Audio and other equipment that consumes large amounts of electricity. IV. Chassis:
(a) Winter rain and snow, roads after the snow, salt water, the car chassis is always directly deal with rain and snow, it is easy to rust. Tires will throw snow with high salinity onto the chassis of the car, making the chassis of the car susceptible to rust. Therefore, before the winter, you should give the chassis a rust-proof care. When you are in the snow, you are not afraid to damage the chassis.
Fifth, car seat:
In winter, the temperature is getting lower and lower, and many car owners can't stand the coldness of leather, eager to get a new ride. As the saying goes, "a good horse with a good saddle" is a must for warm car seats (especially with a backrest) for winter cars, and sheep sheared car seats are just one of the products that can be purchased.
The so-called sheep shearing is to cut the cashmere after the remaining cashmere with a knife, after anti-corrosion treatment, and then dyeing, processed into sheep sheared carpets, cushions, cushions and other indoor supplies.
Identification and price, from the perspective of origin, leather wool cushion sheepskin from the source mainly in Australia, Inner Mongolia and other regions, the cheapest hair quality is also superior, so the current market, the real sheep shearing cushions are more than a thousand dollars, the most The average popular sheep shear cushion is priced at around 1400 yuan.
From the product's point of view, it is not easy to distinguish the naked eye, you can see a few hair with a fire and a fire, the real hair will be the same as the hair into a gray, artificial hair ash into particles. Maintenance and care, currently retailers are not responsible for cleaning sheep shearing cushions, and the average dry cleaners even if the use of dry cleaning methods to wash, it is difficult to restore the original luster. The more glossy the seat cushion is, the more combs are used for finishing the fur and maintain the original color and shape; tapping the surface of the fur with a small stick can hit the dust on the surface of the fur. If it is a slight dust, use a clean cotton cloth to dip a small amount of neutral detergent with warm water or gently wipe with a volatile oil. The water temperature should not be too high. If the stain is too severe, it must be sent to a dedicated dry cleaner for cleaning. During storage, if insect repellents or mothballs are used, they should be wrapped with breathable tissue paper to avoid direct contact with the skin.
Sixth, the door:
Door winter, in addition to the engine should be insulated, but also should prevent the door from freezing, so as not to open when used. To do this, you can inject a little lubricating oil into the door lock hole and seal it around the door.
Desulfurization Slurry Pump also named as FGD Slurry Pump is wild used for the power plant or other industry field, transferring the lime slurry, according to the abrasion and corrosion condition, design and manufacture the Rubber lined FGD pump and All metal FGD pump.
Products detail:
-Single stage, single suction, horizontal centrifugal pump
-Wet parts such as casing, impeller, liner plate in anti-abrasion and
corrosion-resistant high chrome cast iron alloy.
-Mechanical Seal
-Hydraulic optimization design, high
-efficient, energy-saving and stable operation-Back-draw hanger bracket
structure easy for maintaining
FAQ:
Q: How about payment terms?
A: 30% TT deposit + 70% TT before shipment,50% TT deposit + 50% LC balance, Flexible payment
can be negotiated.
Q: Installation and commissioning?
A: We will send our engineer for installation and commissioning, but relevant cost will be paid by you.
Q: Do you have some videos where we can see the line producing?
A: Yes, we can provide some videos for reference.
Series of TL FGD pump is a single stage single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range flowing capacity, high efficiency, high saving power. TL series pump is matched by tight structure X bracket which can save much space.
EX:
600X-TLR The diameter of discharge: 600mm, Rubber liner; bearing lubricating way: Diluted oil ( Thin- oil)
600X-TL The diameter of discharge: 600mm, Metal liner; bearing lubricating way: Diluted oil ( Thin- oil)
Technology features
The pump wet parts are designed by advanced CFD flowing simulating analysis technology to ensure the design reliable and working effective.
It can change the impeller`s position in pump casing by adjusting the bearing unit to keep the pump working high efficiently all the time.
This kind of pump adopt back pull out structure, keeping the simple structure and easy maintenance. Not need disassemble inlet and outlet pipeline.
Two sets of taper roller bearing is fixed at the end of the pump, the column roller bearing is equipped at driving end. The bearing is lubricated by thin oil. All these can improve the bearing working condition and enhance the service life greatly.
Mechanical sealing is adopted integrating mechanical sealing which is specialized in FGD technology to ensure its working.
Material selection:
Our company developed the special anti wear and anti corrosive material which own the duplex stainless steel`s anti-corrosive property and the high chrome white iron`s anti abrasive property in FGD process.
In the rubber pump casing, impeller, suction cover / cover plate are all made of specialized anti-wear and anti-corrosive material ; the material of front liner, back liner and back liner insert are natural rubber with light weight and natural, having excellent anti-corrosive property and low cost.
In metal pump casing, impeller, volute liner, suction plate and back plate are all made of specialized anti wear and anti corrosive material, the suction cover are made of ductile iron with rubber.
KWP
General
Series KWP high-efficiency FGD pump is a new generation energy saving pump.
The KWP pump is single-stage, centrifugal pump which specially used for FGD, environment protection, chemicals, and the paper, sugar and caned food industries. It has the features of high efficiency, non-clogging and back pull out design which can allow the rotor to be removed from the pump casing without disturbing the piping or dismantling the casing. It simplifies maintenance also allows fast inter change of the impellers and wear plate of suction side, thereby allow the pump to be rapidly modified to suit for different operating conditions.
This type pump can deliver all kinds of sewage, clear water, seawater, bittern water, waste water and sludge so that it can be used in water supply plant, sewage treatment works, brewery.
According to the diameter of discharge, the KWP pump is from 40mm to 500mm.
Quantity range: 10~3500CBM/h.
Head range: 5~90m.
These are the frequently used metal material combination for KWP non-clogging pump. According to the different medium delivered by the pump, the pump head could be made of different materials, such as A49,2205, 2605N, 316L, ZG2Cr13, HT250.
Reliable rotor structure:
KWP series products are equipped with the heavy-duty designed bearing based on Germany standard, so the bearing could support more load; Oil lubrication type ensures a smooth and reliable operation, and normally, the service life of such bearing could be over 30,000 hours.
HS,HSR
Type HS/HSR pumps are cantilevered, Horizontal, Centrifugal Slurry Pump. Widely used in electricity, heating, chemical industry, steel, coking, etc of the flue gas desulfurization and desulfurization unit peripheral pump, this series of products with advanced technology, high efficiency and energy saving, the characteristics of reasonable structure, convenient maintenance, the FGD industry preferred products, has been serviced thousand of flue gas desulfurization project for environment protection.
Desulfurization Slurry Pump
Desulfurization Slurry Pump,Anti Abrasive Fgd Recycl Pump,Ksb Fgd Recirculation Pump,Fgd Recycle Pump
Shijiazhuang BKDR Metallurgical Science & Technology Co.,Ltd , http://www.bkdrtech.com