Application of Leaf Humidity Sensor in Sakura Full-Light Spray Tender Cutting Propagation
2019-07-29 14:03:27
The beauty of cherry blossoms is what everyone wants to see. In the cultivation of cherry blossoms, it is usually done in the fall with xylem buds or in the early spring of the following year. In recent years, it has been common to carry out trials on the cutting propagation of cherry blossoms in full sunlight, to maintain the excellent traits of the cherry female parent, shorten the breeding cycle, and to solve the problem of foot foot caused by uneven growth rates of the scion and seedlings in the cherry seedling cultivation. Very important promotion and application value. The spray guarantees the humidity of the foliage and the leaf surface humidity sensor can measure the foliage.
Intermittent spray automatic control equipment is based on the change of the intensity and temperature of sunlight and the response of plant cuttings to water demand, and is designed and manufactured by electronic sensors controlled by computers. Therefore, intermittent spray technology is used for cutting propagation of tender shoots. Under the circumstances, as long as it is not a power outage or the control part fails, its spray equipment will fully control the spray water supply in accordance with the cutting water requirement. Daylight intensity and temperature sometimes become very high during the day, and the spray equipment will automatically increase the number of sprays in order to meet the plant's cutting needs of water at high temperatures, so that on the one hand it can ensure that the plug will not lose water before rooting. On the one hand, the phenomenon of water accumulation due to an increase in the number of water sprays will not occur. This is because the special structure of the cutting bed removes excess water in a timely manner to ensure that it will not cause rot and death due to excessive water spray.
The use of the leaf surface humidity sensor for the determination revealed that when the sunshine intensity and temperature dropped, the transpiration of the leaves also decreased, and the control instrument was automatically controlled to reduce the number of sprays. Since there is no photothermal stimulus to the sensor at night, the automatic control function of the controller will cease to function and the spray will stop. At this time, the timing spray function of the controller can play a role, and the timing spray is performed according to the set time, generally at night. It is set to spray once every half hour. If there is no wind at night and there is dew formation in the weather, the night spray can be stopped. At this time, it can be used for spray sterilization or foliar fertilization. When stabilizing most of the rooting, the number of sprays should be gradually reduced. If secondary root formation occurs in the root system, spraying should be stopped. After hardening for 3 to 5 days, transplanting should be conducted promptly.
Through the analysis of the leaf surface humidity sensor, it can finally be concluded that the use of an all-clear seedling cutting and seedling seeding technique and an intermittent spray method provide moisture to the cuttings and leaves, adjust the temperature and humidity of the cutting bed and the air, and are favorable to the rooting of the cuttings, so that the leaves can be normal. Photosynthesis is used to provide the necessary auxin and nutrients for the rooting of cuttings, thereby facilitating the rapid rooting of cuttings in ventilated, well-drained and clean sterile sand beds, and greatly improving the survival rate of cuttings.
CNC VISION SYSTEM: CCD Vision Cutting system contains two operating modes: direct cutting mode and photo processing mode. Therefore, the processing route manufacturing steps
Differentiate: Direct cutting does not need to draw a photo point, and the tool path file for drawing a photo point can be processed through the buttons on the interface.
Carpet, Felt, Foam, Closed Cell Foam, Fiberglass Insulation, Composites, Gasket Materials, Rubber, Fabric, Honeycomb Cardboard, Single-ply Cloth/Fabric, Corrugated Cardboard/Paperboard, Vinyl Veneers, Snowboard, Corrugated Plastic, Leather Goods, wood veneer for inlay/marquetry artwork, Carbon fiber pre-preg laminates for aerospace, military, and automotive components i.e.
Why choose Oscillating Knife Cutting Machine
Intermittent spray automatic control equipment is based on the change of the intensity and temperature of sunlight and the response of plant cuttings to water demand, and is designed and manufactured by electronic sensors controlled by computers. Therefore, intermittent spray technology is used for cutting propagation of tender shoots. Under the circumstances, as long as it is not a power outage or the control part fails, its spray equipment will fully control the spray water supply in accordance with the cutting water requirement. Daylight intensity and temperature sometimes become very high during the day, and the spray equipment will automatically increase the number of sprays in order to meet the plant's cutting needs of water at high temperatures, so that on the one hand it can ensure that the plug will not lose water before rooting. On the one hand, the phenomenon of water accumulation due to an increase in the number of water sprays will not occur. This is because the special structure of the cutting bed removes excess water in a timely manner to ensure that it will not cause rot and death due to excessive water spray.
The use of the leaf surface humidity sensor for the determination revealed that when the sunshine intensity and temperature dropped, the transpiration of the leaves also decreased, and the control instrument was automatically controlled to reduce the number of sprays. Since there is no photothermal stimulus to the sensor at night, the automatic control function of the controller will cease to function and the spray will stop. At this time, the timing spray function of the controller can play a role, and the timing spray is performed according to the set time, generally at night. It is set to spray once every half hour. If there is no wind at night and there is dew formation in the weather, the night spray can be stopped. At this time, it can be used for spray sterilization or foliar fertilization. When stabilizing most of the rooting, the number of sprays should be gradually reduced. If secondary root formation occurs in the root system, spraying should be stopped. After hardening for 3 to 5 days, transplanting should be conducted promptly.
Through the analysis of the leaf surface humidity sensor, it can finally be concluded that the use of an all-clear seedling cutting and seedling seeding technique and an intermittent spray method provide moisture to the cuttings and leaves, adjust the temperature and humidity of the cutting bed and the air, and are favorable to the rooting of the cuttings, so that the leaves can be normal. Photosynthesis is used to provide the necessary auxin and nutrients for the rooting of cuttings, thereby facilitating the rapid rooting of cuttings in ventilated, well-drained and clean sterile sand beds, and greatly improving the survival rate of cuttings.
CNC Oscillating Knife Cutting Machine
Concepts:
Oscillating Knife: Oscillating Knife cutting has the advantages of small cutting force, low cutting heat, high surface quality of the workpiece, easy chip handling, improved tool durability, stable processing and high production efficiency.CNC VISION SYSTEM: CCD Vision Cutting system contains two operating modes: direct cutting mode and photo processing mode. Therefore, the processing route manufacturing steps
Differentiate: Direct cutting does not need to draw a photo point, and the tool path file for drawing a photo point can be processed through the buttons on the interface.
INDUSTRIES:
Sign and Graphics, Digital Printing, Packaging, Automotive, Recreational boat, Exhibits, and Fixtures, Sign Making, Gasket Materials, Arts and Crafts, etc.
Carpet, Felt, Foam, Closed Cell Foam, Fiberglass Insulation, Composites, Gasket Materials, Rubber, Fabric, Honeycomb Cardboard, Single-ply Cloth/Fabric, Corrugated Cardboard/Paperboard, Vinyl Veneers, Snowboard, Corrugated Plastic, Leather Goods, wood veneer for inlay/marquetry artwork, Carbon fiber pre-preg laminates for aerospace, military, and automotive components i.e.
Why choose Oscillating Knife Cutting Machine
-
Advanced Weihong 53C+TROCEN control system, easy and precise operation;
- The heavy duty thickened bed is welded by square pipe, side hanging
- structure, heavy column, 150*200mm gantry;
- Patent type 1:8 reducer;
- Has the advantages of small cutting force, low cutting heat, high surface quality of the workpiece, easy chip handling, improved tool durability, stable processing and high production efficiency.
- The high precision CNC Oscillating Knife Cutter can induce draft separately and easily cut small pieces.
Main features:
- Working area: Could be customized(1300*2500mm; 1500*3000mm; 2000*3000mm etc.);
- Voltage: 220-420v, 3phase, 50-60hz;
- Spindle:3.5kw air cooling spindle and Oscillating knife+CCD camera;
- X Axis & Y Axis System: Germany ASK/PMT/GC-HIWIN 20 linear guide+Flange slider+Precision 1.25module helical rack+Patent type reducer structure 1:8
- Table: Vacuum & T-slot table;
- Precision machined aluminum parts, using aviation aluminum T6061/6063 material, CNC processing center precision manufacturing.
Oscillating Knife Cutter With CCD
Oscillating Knife Cutter With Ccd,Oscillating Knife Cutter,Cnc Router With Oscillating Knife,Oscillating Knife Atc Contour Cutter
Shandong U-May CNC Technology Co., Ltd. , http://www.fiberlasers.de